Sewing Tips and Tricks Midland TX

Is there a trick to sewing bias tape around curves without it twisting and cupping? What kind of lining should I use in a silk suit? Which presser foot should I use to attach beads? Read on to find the answers to questions like these.

Lizard Lady Adventures
(956) 454-3601
P.O.Box 10931
Midland, TX
 
Delavan Mary Jo
(432) 682-3154
4615 Wilshire Dr
Midland, TX
 
S G O Designer Glass
(432) 520-8788
309 Dodson St Ste B
Midland, TX
 
Folger Galleries
(432) 697-3778
3211 W Wadley Ave
Midland, TX
 
Hobby Lobby Creative Center
(432) 697-0784
4715 Billingsley Blvd
Midland, TX
 
Quatro Paint Products Corp
(432) 520-4466
2910 W Wall St
Midland, TX
 
Kelly Moore Paints
(432) 697-4103
205 N Midkiff Rd
Midland, TX
 
Hancock Fabrics
(432) 683-5502
15 Meta Dr
Midland, TX
 
Midland Gallery
(432) 694-8761
4610 N Garfield St
Midland, TX
 
FastFrame
(432) 520-5137
4415 Northcrest Dr Apt 2012
Midland, TX
 

Sewing Tips and Tricks

Linda Lee, our Q&A expert, welcomes your questions. Direct your e-mails to her at sewnews@sewnews.com.

Bias Opinion

Is there a trick to sewing bias tape around curves without it twisting and cupping?

Audrey

There are some very fancy bias binder attachments available for most machines. These attach and stitch bias tape to an edge in one step, but there's a better way that doesn't require any special equipment. For the best finished look, choose a double or French bias tape or cut your own bias pieces to customize the color and vary the size.

Cut bias strips six times your preferred finished width, plus an additional 1/8∗-1/4∗ depending on the fabric thickness. The thicker the fabric, the more you should add to the width. Fold the strip in half lengthwise before applying it to the edge. Pin the raw binding edges to the project raw edge. As you're working around the curve, give the binding a little shove, easing as much fullness into the application as you can without creating puckers. This will keep the binding flat when finished.

Stitch the binding to the project along the seamline. Trim the seam allowance to an even width that's slightly narrower than the finished binding width. Wrap the binding around the raw edges, keeping it as snug as possible against the edge. The outer folded edge should lie beyond the seamline on the project wrong side. Pin frequently in the seam well, parallel to the outer edge. Stitch in the ditch from the right side so that the stitches are both hidden in the seam well and catching the folded edge on the fabric wrong side.

Suited for Silk

What kind of lining should I use in a silk suit?

Carolyn

The best all-purpose lining for most projects and fabrics is Bemberg rayon. You can find this in most independent fabric stores or online. It's lightweight but durable. I also recommend using China silk for a very lightweight lining, although it's less durable and can shred at stress points over time. Avoid using polyester lining in a silk garment. It's too stiff and doesn't conform to the characteristics of a nice silk.

Ruffle Trouble

I'm covering seat cushions for my kitchen chairs. How do I calculate the amount of fabric needed for a ruffle around each cushion?

Michael

First, decide whether you want a single-layer ruffle that's hemmed on one edge or if you want a ruffled that's folded in half, so the fabric right side is visible on both sides. Either way, measure the circumference of the seam cushion. Multiply that measurement by at least two and add a few inches. Most ruffles are double the fullness. Next, calculate the desired width of the ruffle and decide whether the ruffle will be single or double-sided. Cut enough strips to stitch together and form one long piece.

For the Beads

Which presser foot should I use to attach beads?

Anonymous

Look for a presser foot that has a scooped out tunnel on the foot bottom that's large enough to travel over the beads. Manufactu...

Click here to read the rest of the article from Sew News

© Creative Crafts Group, LLC. All rights reserved.