» » »

Couture Zipper Setting Technique Benton AR

There are dozens of ways to set a zipper into a fly placket, but this couture method delivers excellent results. I first discovered this application on a pair of Yves Saint Laurent pants, and you'll find that it belies any notion that couture techniques are difficult. Please feel free to read the following article to find more information on sewing tips.

Hobby Lobby
(501) 224-3277
12201 West Markham Street
Little Rock, AR
Customer Rating
Customer Rating

Customer Review
Company Rating (on scale of 1 to 5) = 3(1 person reviewed this company)
  • Variety of Products 3.5
  • Pricing 3
  • Helpfulness of Staff 2.5


Alllied Glass and Frame Shop
(501) 778-1636
115 E Sevier St
Benton, AR
 
Dianne Roberts Art Studio & Gallery
(501) 860-7467
110 N Market St
Benton, AR
 
Allied Glass & Frame Shop
(501) 778-6244
115 E Sevier St
Benton, AR
 
Hobby Lobby Creative Centers
(501) 224-3277
12201 W Markham St
Little Rock, AR
 
Michael's Arts Crafts
(501) 224-4989
11400 West Markham Street
Little Rock, AR
 
Office Depot
(501) 776-1368
1621 Military Rd
Benton, AR
Recycling Services
Recycle Ink, Ink Cartridges, Cell Phones, Batteries

All About Art & Framing
(501) 778-6457
807 W South St
Benton, AR
 
Tandy Leather Factory
(501) 407-9104
1 Stagecoach Vlg
Little Rock, AR
 
The Art of Framing
(501) 223-8787
11323 Arcade Dr
Little Rock, AR
 

Couture Zipper Setting Technique

How To
Couture With Claire

Sew Professional
with Claire Shaeffer

There are dozens of ways to set a zipper into a fly placket, but this couture method delivers excellent results. I first discovered this application on a pair of Yves Saint Laurent pants, and you'll find that it belies any notion that couture techniques are difficult.

The Fly Zipper
In this couture method, the fly opening is machine stitched first. Then the zipper is sewn into the opening by hand. This procedure allows you to set the zipper into any type of opening (slot, lapped, bound or fly) with the control that hand sewing permits, but without sacrificing the integrity of the design. The stitching also reinforces the edges and holds the layers flat. In couture, fly plackets are usually finished with extended facings that are cut as a part of the front, instead of with a separate facing like men's trousers. The result is more flattering and less bulky.

Prepare the Placket
Mark the foldlines on the overlap and underlap pieces at the zipper opening with long hand-basting stitches.

If the opening has an interfacing pattern, fuse or sew the interfacing fly piece to the fly extensions on the fabric wrong side (1). If the pattern doesn't have an interfacing pattern, create one by tracing the fly extension section that will be folded to the fabric wrong side.

Cut a 1Ú2"-wide fabric strip from lightweight silk to create a stay for the fly opening of each pant piece. The stay length should be approximately that of the pattern fly opening. Moisten and press the strip to remove the fabric stretch.

Position the stays over the marked foldlines on the fabric wrong side of each pant front piece. Pin the stay ends in place; then pin toward the stay center, easing the pant fabric as needed. Use a long running stitch to sew the stay in place (2).

Stitch the pant front pieces together at the center front, beginning at the zipper opening lower edge and ending about 2" from the pant inseams (3).

Fold under the seam allowances on both sides of the placket; baste G" from the folded edge beginning at the opening lower edge. Baste the waist edge. Press the folded edges.

Prepare the Zipper
Press the zipper tape to remove any folds. If the zipper is longer than the opening, measure beginning at the upper edge and mark the finished length. At the marked length, stitch a thread bar over the zipper teeth.

Cut off the zipper H" to 1" below the thread bar.

Overcast-stitch or bind the zipper lower edge.

Set the Zipper
On the right pant front (overlap) piece, mark the fly stitching line using thread tracing or chalk. With the fabric right side up, stitch along the marked line, ending at the crotch seamline (4). Pull the threads through to the wrong side using a calyx-eyed needle. Knot and trim the thread ends.

On the left pant front (underlap), stitch close to the folded edge, keepin...

Click here to read the rest of the article from Sew News

© Creative Crafts Group, LLC. All rights reserved.