Candy Cauldron Winter Park FL

Do you want to know what do you need and how do you prepare if you want to make a candy cauldron? Please feel free to read the following article to find out the answer of this question.

Michael's Arts Crafts
(407) 831-2237
375 East Altamonte Drive
Altamonte Springs, FL
 
Michael's Arts Crafts
(407) 302-0232
111 Towne Center Boulevard
Sanford, FL
 
Arl Lev Art
(407) 470-1355
1220 E Livingston St
Orlando, FL
 
My Art Studio
(407) 894-5950
4882 New Broad St
Orlando, FL
 
Art Lando
(407) 423-4088
213 N Magnolia Ave
Orlando, FL
 
Michael's Arts Crafts
(407) 226-1134
6725 South Kirkman Road
Orlando, FL
 
Local Color Art Studio
(407) 841-9996
1309 Edgewater Dr, Ste 2
Orlando, FL
 
Sam Flax Art & Design Store
(407) 898-9785
1401 E Colonial Dr
Orlando, FL
 
Atlantis Art Glass Studio Inc
(407) 896-9116
809 Virginia Dr
Orlando, FL
 
Western Crafts & Gifts
(407) 578-6833
5600 W Colonial Dr
Orlando, FL
 

Candy Cauldron

WHAT YOU NEED

  • 1 yard of Halloween-print cotton fabric
  • 1 yard of coordinating fleece
  • 5-quart paint bucket
  • Polyester fiberfill
  • Coordinating all-purpose thread
  • Hand sewing needle
  • Hot glue gun
  • Rotary cutting supplies (optional)

Use 1/2" seam allowances unless otherwise noted.

Preparation

Fold the fleece in half, matching the selvage edges, and then fold the fleece in half widthwise. Position the circle template below along the foldline; cut (1).


From the cotton fabric, cut one lining template circle from below; transfer the markings.

From the cotton fabric, cut four 7 1/4"x9” rectangles for the panels, two 4”x32” rectangles for the tie, four 4”x24 3/4” rectangles for the band and one 2 1/2"x32” rectangle for the handle casing.

Construction

Position two panel pieces with right sides facing. Stitch one long edge. Repeat to stitch the remaining two panels. Stitch the resulting panel 9” edges to form a tube (2).


Stitch 1/2” above the tube lower edge using a long machine stitch. Clip every 1”, making sure not to cut through the stitching (3).


With right sides facing, align the marks on the fabric lining piece with the lower panel seams. Pin along the clipped tube edge; stitch.

With two band strips right sides facing, stitch one short edge. Repeat to stitch the remaining two band strips.

Stitch the resulting band strips along the short edge with right sides facing to form a tube.

With right sides facing, align the band raw edges with the large fleece circle perimeter; stitch.

Turn the raw band edge toward the large circle wrong side; press. Topstitch 1/2” from the fold (4).


With right sides facing, stitch the two tie pieces along one short edge.

Fold the tie in half lengthwise with right sides facing. Stitch the tie perimeter, leaving a 3” opening on one long edge for turning.

Turn the tie right side out; press. Slipstitch the opening closed.

Fold the handle casing in half lengthwise with right sides facing; stitch the long edge.

Turn the handle casing right side out; press. Topstitch 1/8” from each long edge.

Bucket Construction

Remove the handle from the bucket and insert it through the fabric handle casing.

Place the fabric lining in the bucket. Fold the excess fabric over the bucket edge.

Using an awl or other sharp tool, poke a hole on each lining side where the handle will be reinserted.

Baste the exterior circle perimeter 2 1/2” inside of the finished edge.

On a flat work surface, position the exterior circle right side up so the fabric band right side is exposed. Center the bucket over the fabric circle (5).


Gently pull the basting thread tails to gather the large fabric circle around the bucket.

Stuff polyester fiberfill between the fabric and the bucket until the desired fullness is achieved.

Tightly pull the gathering sti...

Click here to read the rest of the article from Sew News

Local Events

Friends of the Bandshell Summer Concert Series
Dates: 8/25/2012 – 8/25/2021
Location:
Ocean Walk Shoppes- Bandshell - Daytona Beach, FL Daytona Beach
View Details
 
© Creative Crafts Group, LLC. All rights reserved.