» » »

Candy Cauldron Monroe LA

Do you want to know what do you need and how do you prepare if you want to make a candy cauldron? Please feel free to read the following article to find out the answer of this question.

Laseter's Gallery & Frame Shoppe Inc
(318) 323-0697
1201 Forsythe Ave
Monroe, LA
 
Databank Imx
(318) 387-9890
3000 Desoto St
Monroe, LA
 
Inglenook Frame Gallery
(318) 387-1755
200 Hudson Ln
Monroe, LA
 
Hancock Fabrics
(318) 325-1763
301 Sterlington Rd
Monroe, LA
 
Michaels Arts & Crafts
(318) 322-6338
4429 Pecanland Mall Dr
Monroe, LA
 
Michaels
(318) 387-9263
2700 Louisville Ave
Monroe, LA
 
Fabulous Fabric
(318) 410-8106
1803 Lamy Ln
Monroe, LA
 
Crosscraft Enterprises
(318) 343-9220
18 Jana Dr
Monroe, LA
 
KT Hobbies
(318) 342-9155
7909 Desiard St
Monroe, LA
 
tyteeanna jackson art and crafts
(318) 496-9691
318-496-9691
bastrop, LA
 

Candy Cauldron

WHAT YOU NEED

  • 1 yard of Halloween-print cotton fabric
  • 1 yard of coordinating fleece
  • 5-quart paint bucket
  • Polyester fiberfill
  • Coordinating all-purpose thread
  • Hand sewing needle
  • Hot glue gun
  • Rotary cutting supplies (optional)

Use 1/2" seam allowances unless otherwise noted.

Preparation

Fold the fleece in half, matching the selvage edges, and then fold the fleece in half widthwise. Position the circle template below along the foldline; cut (1).


From the cotton fabric, cut one lining template circle from below; transfer the markings.

From the cotton fabric, cut four 7 1/4"x9” rectangles for the panels, two 4”x32” rectangles for the tie, four 4”x24 3/4” rectangles for the band and one 2 1/2"x32” rectangle for the handle casing.

Construction

Position two panel pieces with right sides facing. Stitch one long edge. Repeat to stitch the remaining two panels. Stitch the resulting panel 9” edges to form a tube (2).


Stitch 1/2” above the tube lower edge using a long machine stitch. Clip every 1”, making sure not to cut through the stitching (3).


With right sides facing, align the marks on the fabric lining piece with the lower panel seams. Pin along the clipped tube edge; stitch.

With two band strips right sides facing, stitch one short edge. Repeat to stitch the remaining two band strips.

Stitch the resulting band strips along the short edge with right sides facing to form a tube.

With right sides facing, align the band raw edges with the large fleece circle perimeter; stitch.

Turn the raw band edge toward the large circle wrong side; press. Topstitch 1/2” from the fold (4).


With right sides facing, stitch the two tie pieces along one short edge.

Fold the tie in half lengthwise with right sides facing. Stitch the tie perimeter, leaving a 3” opening on one long edge for turning.

Turn the tie right side out; press. Slipstitch the opening closed.

Fold the handle casing in half lengthwise with right sides facing; stitch the long edge.

Turn the handle casing right side out; press. Topstitch 1/8” from each long edge.

Bucket Construction

Remove the handle from the bucket and insert it through the fabric handle casing.

Place the fabric lining in the bucket. Fold the excess fabric over the bucket edge.

Using an awl or other sharp tool, poke a hole on each lining side where the handle will be reinserted.

Baste the exterior circle perimeter 2 1/2” inside of the finished edge.

On a flat work surface, position the exterior circle right side up so the fabric band right side is exposed. Center the bucket over the fabric circle (5).


Gently pull the basting thread tails to gather the large fabric circle around the bucket.

Stuff polyester fiberfill between the fabric and the bucket until the desired fullness is achieved.

Tightly pull the gathering sti...

Click here to read the rest of the article from Sew News

© Creative Crafts Group, LLC. All rights reserved.