Candy Cauldron Brentwood TN

Do you want to know what do you need and how do you prepare if you want to make a candy cauldron? Please feel free to read the following article to find out the answer of this question.

Michael's Arts Crafts
(615) 731-3781
5360 Mount View Road
Antioch, TN
 
Phoenix Framing
(615) 385-2595
3326 Aspen Grove Dr Ste 506
Franklin, TN
 
B A Framer Custom Framing
(615) 771-7393
Cool Springs Xing
Franklin, TN
 
Framo Product Framers & Fine Art
(615) 244-4642
722 Melrose Ave
Nashville, TN
 
Art Is Heaven Gallery
(615) 460-7404
2019 8th Ave S
Nashville, TN
 
Michael's Arts Crafts
(615) 385-5344
1 Hundred Oaks Sho
Nashville, TN
 
Frames Unlimited
(615) 790-2942
116 Royal Oaks Blvd
Franklin, TN
 
Tandy Leather Company
(615) 833-1635
4740 Nolensville Pike
Nashville, TN
 
RuBee's Candles
(615) 649-4479
6629 Christiansted Lane
Nashville, TN
Prices and/or Promotions
Pure Beeswax Candle From Nashville, TN

Karen Hollywoods Pre to Post Modern
(615) 292-1958
2110 8th Ave S
Nashville, TN
 

Candy Cauldron

WHAT YOU NEED

  • 1 yard of Halloween-print cotton fabric
  • 1 yard of coordinating fleece
  • 5-quart paint bucket
  • Polyester fiberfill
  • Coordinating all-purpose thread
  • Hand sewing needle
  • Hot glue gun
  • Rotary cutting supplies (optional)

Use 1/2" seam allowances unless otherwise noted.

Preparation

Fold the fleece in half, matching the selvage edges, and then fold the fleece in half widthwise. Position the circle template below along the foldline; cut (1).


From the cotton fabric, cut one lining template circle from below; transfer the markings.

From the cotton fabric, cut four 7 1/4"x9” rectangles for the panels, two 4”x32” rectangles for the tie, four 4”x24 3/4” rectangles for the band and one 2 1/2"x32” rectangle for the handle casing.

Construction

Position two panel pieces with right sides facing. Stitch one long edge. Repeat to stitch the remaining two panels. Stitch the resulting panel 9” edges to form a tube (2).


Stitch 1/2” above the tube lower edge using a long machine stitch. Clip every 1”, making sure not to cut through the stitching (3).


With right sides facing, align the marks on the fabric lining piece with the lower panel seams. Pin along the clipped tube edge; stitch.

With two band strips right sides facing, stitch one short edge. Repeat to stitch the remaining two band strips.

Stitch the resulting band strips along the short edge with right sides facing to form a tube.

With right sides facing, align the band raw edges with the large fleece circle perimeter; stitch.

Turn the raw band edge toward the large circle wrong side; press. Topstitch 1/2” from the fold (4).


With right sides facing, stitch the two tie pieces along one short edge.

Fold the tie in half lengthwise with right sides facing. Stitch the tie perimeter, leaving a 3” opening on one long edge for turning.

Turn the tie right side out; press. Slipstitch the opening closed.

Fold the handle casing in half lengthwise with right sides facing; stitch the long edge.

Turn the handle casing right side out; press. Topstitch 1/8” from each long edge.

Bucket Construction

Remove the handle from the bucket and insert it through the fabric handle casing.

Place the fabric lining in the bucket. Fold the excess fabric over the bucket edge.

Using an awl or other sharp tool, poke a hole on each lining side where the handle will be reinserted.

Baste the exterior circle perimeter 2 1/2” inside of the finished edge.

On a flat work surface, position the exterior circle right side up so the fabric band right side is exposed. Center the bucket over the fabric circle (5).


Gently pull the basting thread tails to gather the large fabric circle around the bucket.

Stuff polyester fiberfill between the fabric and the bucket until the desired fullness is achieved.

Tightly pull the gathering sti...

Click here to read the rest of the article from Sew News

© Creative Crafts Group, LLC. All rights reserved.